thought these forums were to help each other out with problem solving etc
38 views on my last post
not 1 single reply
thought these forums were to help each other out with problem solving etc
38 views on my last post
not 1 single reply
Probably to do with the fact it is about Corel product, you might do better on a Corel forum.
Christine
Software: XDPX9, WD9,WD10,XDPX10,WD11,XDPX11,XDP365
Yeah there are only a few Corel users in this forum. Though if I might say, a quite a few former Corel users.
Gary W. Priester
gwpriester.com | eyetricks-3d-stereograms.com | eyeTricks on Facebook | eyeTricks on YouTube | eyeTricks on Instagram
Well your Post now has 63 views and no response to your queries:
- You have a trial version of corel x7
- I airbrush
- You intend to get a small laser cutter to cut out stencils
- Please make it simple to understand
Where would anyone start or care to?
You are not asking for a solution to a problem, you are after on-the-job training with unlimited support.
How many TGers airbrush AND use Corel AND make stencils for laser cutting AND have a cutter AND can advise you with generic answers to your specific but variable starting position?
Go figure,
Acorn
Acorn - installed Xara software: Cloud+/Pro+ and most others back through time (to CC's Artworks). Contact for technical remediation/consultancy for your web designs.
When we provide assistance, your responses are valuable as they benefit the community. TG Nuggets you might like. Report faults: Xara Cloud+/Pro+/Magix Legacy; Xara KB & Chat
Probably nobody.
Me, I wouldn't touch Corel with a 10 foot pole, not because its bad software, but Corel bought out my preferred software (at the time) Micrografx Designer and then dumped it, so I have an issue with the company, Corel, not the software. I purchased an air brush once with the intent to use it and I never did. Laser cutters are for cheap low end products like key chains (not a business I'd even consider). So there's nothing in your previous question that I could give any kind of answer, nor care to... so as Acorn stated, I can't help you (and likely no one else either). Your issues are so specific, that unless someone is involved in everything that you are could an answer even be given. I think you're just out of luck.
Visit a Corel forum is probably the best advice given so far.
OK Here's another Corel response that should be helpful http://www.talkgraphics.com/showthre...114#post542114
Gary W. Priester
gwpriester.com | eyetricks-3d-stereograms.com | eyeTricks on Facebook | eyeTricks on YouTube | eyeTricks on Instagram
GRAMSAM, sorry, but I seem to have scared you away - "not 1 single reply".
Acorn
Acorn - installed Xara software: Cloud+/Pro+ and most others back through time (to CC's Artworks). Contact for technical remediation/consultancy for your web designs.
When we provide assistance, your responses are valuable as they benefit the community. TG Nuggets you might like. Report faults: Xara Cloud+/Pro+/Magix Legacy; Xara KB & Chat
Oh well, we're here if he's interested enough to send a sample file as suggested in http://www.talkgraphics.com/showthre...114#post542114
I am a Corel (PaintShop Pro X8) user, but haven't a clue what the question is about
As suggested, try the Corel User to User Web Forum:
http://forum.corel.com/EN/viewforum.php?f=56
And for those who are so negative.
Yes, Corel have taken a long time to get PaintShop Pro back to full usefulness (maybe not a word..)
PSPX8 is excellent (I use it every day, rather more than I care to admit).
I for one would not touch The Mudhut product with a barge-pole.
Tsk tks, such negativity, didn't expect that here, this is such a friendly group :-(
Grenou
Hi,
I have CorelDraw X3 on my system if you want to attach or e-mail me the file in question I will see if I can
open it
Jim
Intel i7-2600 processor 3.4GH, Windows 10 64Bit, 12GB Memory, Geforce 960 2Gb graphics card
Bookmarks