You're correct Sadler, for some reason with the contstraint set at 30 degrees, on rotation it snaps to 14.10, 30, 60, 75.80 & 90
Egg
Minis Forum UM780XTX AMD Ryzen7 7840HS with AMD Radeon 780M Graphics + 32 GB Ram + MSI Optix Mag321 Curv monitor + 1Tb SSD + 232 GB SSD + 250 GB SSD portable drive + ISP = BT + Web Hosting = TSO Host
Thanks for confirming that Egg. Note that it is not just 30 - almost any angle constraint doesn't. Also applies to earlier versions though was working as expected a few versions back. Perhaps it will be put straight before the imminent XX release.
Will it not simply be a feature of the number of control points a shape has?
If the object is a line, I get 12 x 30 degs.
With a random shape, I was getting 0.3, 20.3 30, 30.3 etc.
What I do is rotate the object using the right mouse button and watch the Angle window and left click on the required angle when the Ctrl key is held down.
Acorn
Acorn - installed Xara software: Cloud+/Pro+ and most others back through time (to CC's Artworks). Contact for technical remediation/consultancy for your web designs.
When we provide assistance, your responses are valuable as they benefit the community. TG Nuggets you might like. Report faults: Xara Cloud+/Pro+/Magix Legacy; Xara KB & Chat
I thought this might be the cause initially Acorn, so to eliminate this possibility I placed the shape well within the confines of an outer circle and grouped the two, thus elimainting various control points as it was now a perfect circle. It showed the same error. The constraint was never 30, 60, 90 etc but some very odd angles.
View in HD
Egg
Minis Forum UM780XTX AMD Ryzen7 7840HS with AMD Radeon 780M Graphics + 32 GB Ram + MSI Optix Mag321 Curv monitor + 1Tb SSD + 232 GB SSD + 250 GB SSD portable drive + ISP = BT + Web Hosting = TSO Host
Thanks again for doing the vid Egg. Just to confirm - angle constraint works as expected without any fractional angles and with any shape and any centre in Xara PGD 7.
Yes that appears to be the case Sadler, it's a bug that's crept in on later versions. Personally I never use the constraint feature, prefering to type the required rotation angle into the rotation text box each time.
Egg
Minis Forum UM780XTX AMD Ryzen7 7840HS with AMD Radeon 780M Graphics + 32 GB Ram + MSI Optix Mag321 Curv monitor + 1Tb SSD + 232 GB SSD + 250 GB SSD portable drive + ISP = BT + Web Hosting = TSO Host
I tried it in xdpx
square: - works fine with both 30deg and 45deg
triangle: works with 30deg, but not 45 deg
above three point... starts to 'play up'
I think it has to do with where the centre of rotation is relative to the actual centre of the shape [as opposed to the boundary handles]...
But if this were the case, surely enclosing it within a circle and grouping ensures the centre of rotation is the centre of the circle?
Egg
Minis Forum UM780XTX AMD Ryzen7 7840HS with AMD Radeon 780M Graphics + 32 GB Ram + MSI Optix Mag321 Curv monitor + 1Tb SSD + 232 GB SSD + 250 GB SSD portable drive + ISP = BT + Web Hosting = TSO Host
don't know with version 9 egg I don't have it - just passing on the results I got with version 8 for the record
how did you centre the star in the circle? - using the alignment tool won't work, as that goes by boundary box [had a discussion about that earlier in another thread] - if it wasn't centred according to geometry rather than BBox, just grouping it might not be enough?
Last edited by handrawn; 10 June 2014 at 11:11 PM. Reason: tit, I ask you...
Bookmarks